1. Features of LED fluorescent lamp aging line:

1. This equipment is dedicated to the detection of aging of 220V, 110V LED energy-saving fluorescent lamps. Through the aging of 220V LED energy-saving fluorescent lamps in high voltage, medium voltage, normal pressure, low voltage, high temperature, roaming, impact and other voltage areas, observe the LED Whether the energy-saving fluorescent lamp can pass the aging test of the above voltage range. This product is a patented product approved by the Patent Office (Patent No.: ZL 2012 2 0526602.7)

2. The tooling board can age the LED energy-saving fluorescent tubes, and can fully meet the product aging time requirements.

3. There are 106 chain plates in the whole line (according to the length of the aging line), each chain plate is equipped with 16 E27 five-magazine lamp sockets, 4 pairs of T8 fluorescent lamp sockets, 1696 aging bulb lamps or 424 fluorescent tubes (Full delivery).

2. Key technical points of LED fluorescent lamp aging line:

1. Constant temperature zone: The constant temperature system is completed by electric heating. The lower 5 meters are set as the heating section, and the second meter is equipped with two 1KW ceramic heating tubes, 3 temperature collection points, and the temperature is automatically controlled as: room temperature + 80°C. 2. Detection of the impact beat circuit: a Tianzheng brand voltage regulator 10KW voltage regulator 1 0-250V adjustable, 6 zones are set up across the line, and the impact time of each zone can be set on the touch screen interface. 3. Test the normal voltage circuit: use Tianzheng brand voltage regulator 10KW voltage regulator 1 0-250V adjustable, set as low voltage test area. (The area range is about 7 meters). 4. Detect low-voltage circuit: use Tianzheng brand voltage regulator 10KW voltage regulator 1 0-250V adjustable, set as low-voltage test area. (The area range is about 7 meters). 5. Detection of high-voltage circuit: use Tianzheng brand voltage regulator 10KW voltage regulator 1 0-300V adjustable, set as high-voltage test area. (The area range is about 7 meters). 6. The bulb lamp adopts E27 screw socket. 7. The lamp is used for aging, and it is equipped with a fast T8 lamp holder fixture. (The lamp holder fixture can be adjusted to 300, 600, 900, 1200MM);

3. Appearance protection requirements of LED fluorescent lamp aging line:

1. The fuselage and frame are made of 40*40*1.5 (MM) steel pipe welding, the upper and lower parts of the fuselage are made of 130*23 (MM) special aluminum alloy profiles for aging lines, and the guard plate is made of 1.5MM cold plates. 2. The transmission chain adopts inch double-pitch single ear double-hole chain; 3. A light-blocking passport is set on the online body, and the combination of plexiglass and aluminum profile is used to effectively reduce the glare of the energy-saving lamp and better protect the eyes.

Fourth, the appearance protection requirements of the LED fluorescent lamp aging line:

1. The whole line is equipped with two electric trough rails, using edge epoxy board. And assembling 3MM thick copper conductive strip. The line body is equipped with a protective anti-drop net to prevent the product from falling and breaking. The high-quality stainless steel fine mesh net is fixed with angle iron on both sides. 2. The equipment must not rust or generate dust. 3. Equipment noise: below 65dB. 4. The feet are equipped with galvanized adjustable level and height adjustable foot cups. 5. The total length of the line body: 10 meters, the height between the working surface and the ground is 750±20mm, adjustable. 6. Dimensions: L10000mm*W1620mm*1270mm

5. Power and transmission of LED fluorescent lamp aging line:

1. The motor adopts Taiwan Kun 1.5KW three-phase motor, 1:200 reducer, 2HP frequency converter, frequency conversion speed regulation, linear speed 0-2M/min adjustable, aging time 0-4 hours adjustable. 2. It adopts 1 inch T17 tooth double pitch sprocket with φ50 main shaft and tensioning mechanism as the transmission device.